Why Understanding Plumbing Basics is Essential For Installing a Bathtub
Why Understanding Plumbing Basics is Essential For Installing a Bathtub
Blog Article
We have encountered this post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and think it made sense to share it with you on this site.
Setting up a tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, and also often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately hard task. If the old bathtub is easily available, the project can relocate immediately; if you have to open up a wall to eliminate the old bathtub as well as place the brand-new tub, the task is much harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and set in the new one. Make certain you have actually qualified on your own for the job and also are comfortable attempting it. As opposed to working with a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This short article will help you mount a brand-new bathtub in your washroom if you have actually already gotten a new tub and also do not require to transform the setup of your previous water pipes.
Your tools and product list ought to comprise the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The process of removing the existing taps can be quite problematic as a result of the limited access that is usually the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washers are in place in between the faucet and the sink. Protect the tap in place with the maker supplied backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind ought to be connected to the tap finishes first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and readjusting the feet on the tub up until the level checks out level.
To install taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water and examine all joints as well as new pipework for leaks as well as tighten them if needed. Fill the bath tub and additionally examine the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and securing around the bath tub ought to wait up until the bath tub has been utilized a minimum of once as this will certainly resolve it into its final position.
Getting ready for the Installation
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to prevent strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to crack a rigid seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, bring about difficulties with wetness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently offered on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were guided to that write-up on Tools You Need to Install a New Bathtub through an associate on another web property. You should take a moment to promote this blog if you liked it. I appreciate reading our article about Tools You Need to Install a New Bathtub .
Dial immediately! Report this page